Holy guacamole. This is a big darn bed. I’m so glad I finally get to reveal it to you!
I have been wanting to build my own bed for years now. I had a beautiful store bought bed prior to this albatross. I loved it, but have always had the itch to create one myself. I ran across my inspiration at a store called Arhaus. The store is full of inspiration… As well as very hefty price tags. The original bed before shipping and tax for them was $3699.00. Nope, that was not a typo. I am happy to say that I built my version for under $400. (Insert happy dance) Check it out… My new DIY King Size Bed Free Plans!
Yah. I love it. A whole lot.
As always, I will walk you through this entire build here (with 42 photos… you have been warned) and you can also download and print the FREE plans by clicking HERE or the button below!
The posts of this bed are 4×4. These are untreated boards and can be found at both big hardware stores. You won’t be able to cut through a 4×4 without a 12″ miter saw. So, if yours is smaller, you can have the hardware store make these few cuts. You can also use a hand saw with a little elbow grease. Or, upgrade your saw! I use Ridgid’s 12″ sliding compound miter saw, but I am so pumped to try out Ryobi’s new 12″ sliding miter that comes out in a few weeks!
I decided to attach all of the planks before building the actual headboard support so I could get an exact measurement. I used white wood boards to keep the cost down, and I love how rustic they look when stained. I used my Kreg Jig for this entire build. I use the K5, but I also own the K4 and the new Foreman. I love every single one of them for different reasons. If you are looking to invest and get one, I would go for the K5. It’s a small amount more than the K4, but I find that it’s much more user friendly and has lots of upgrades that make it my fav. And, it’s easy enough for a beginner. In fact, I would suggest beginning with a Kreg Jig. They make building much easier.
Watch our How to Use a Kreg Jig Video HERE!
Let me explain how I did the pocket holes on the headboard. This uses 1×6 and 2×6. I didn’t do pocket holes in any of the 2×6. I did most of the planks with 3/4″ pocket holes down one side like this…
When I lined all of my boards up, you can see that on the boards sitting next to the 2×6 boards, I did pocket holes down both sides. This allowed me to attach into the 2×6 as well as the next plank.
Once I had that finished I took the measurement to build the frame that sits behind it. For this I used 2×3 boards and made 1.5″ pocket holes on each end. I used 2.5″ pocket hole screws to attach them to the 4×4 posts. You want the face of the support to sit 1.5″ from the front of the posts. This will allow it to all line up correctly. Once the frame was made, I laid it on the back side of the planks. I used wood glue and 1.25″ finish nails with my Ryobi 16G finish nailer to attach through the frame and into the planks.
Next, you will add trim pieces. These are simple cuts. I measured the space exactly on each one rather than going from the plan. I used wood glue and finish nails through these pieces and into the front of the headboard.
Next, you will add the 2×6 boards. These are heavy. I used a good amount of wood glue and 2″ finish nails to attach it in place. I also ran a few wood screws through the back of the headboard after that and into the 2×6 just to be extra safe.
I also added the top board at this point. After glueing and nailing it with 2″ nails, I did add some wood screws through the top and into the headboard just to be extra safe.
See my new Kreg clamps?? I love them. I have 4 and I want 36 They are like having an extra set of hands around and they are so simple to use.
Headboard finished. Moving onto footboard.
This is basically the exact same build as the headboard with different measurements. I did do everything the same though. Here are some photos to show you…
I did use 1×4 for the supports on the footboard since it wasn’t as large as the headboard. I used my right angle clamp to hold it all in place while I attached using 2.5″ pocket hole screws into the leg.
Now the 2×6 runners…
I used PureBond Plywood for the base of the side rails. I had the guys at Home Depot rip mine to size so I could get it home easy. I used Birch. You will start with two pieces that look like this…
I used a new fav stain color on my bed. It’s called Ash by Varathane and you can find it at Home Depot. It’s not a very dark brown, but where the grain catches the stain it really goes a black tone which I love.
Now putting it together… This was something I did enlist lots of help on. My hubby and his friend moved the headboard in first. Then I cut a few 4×4 scraps to help hold the rails in place while I used 2.5″ pocket hole screws through the pocket holes on the rails and into the legs.
After that I did the same to the footboard. Finally, I cut all of the planks to run under the mattress. These all use a block under them to support the weight of the mattress. I nailed them in place with 2″ finish nails into the runners on the sides.
But… I LOVE IT. I will say… This is not a super advanced build by any means. All of the cuts are straight and many are the same. I would say it is very labor intensive. I was sore for two days after building it… Which really is more a testament to my physical health, but we’ll blame the bed.
I hope you LOVE it as much as I do!
The bedding was a Valentine’s gift from my hubby. It’s all from Restoration Hardware.
The large metal ampersand magnet board can be found HERE!
The color on the walls is Valspar Homestead Resort Parlor Taupe.
The mirrors are from Hobby Lobby as well as the hooks I used to hang them. Wayfair carries one that is very similar and super cute HERE!
The nightstands are a little sneak peek for next week or so… One isn’t totally finished but you guys will love them!
Original article and pictures take www.shanty-2-chic.com site
Комментариев нет:
Отправить комментарий